| jtaylor12008
| 293
| 2008-04-05 23:18:28
| 1982 s10 w/ 327 sb
|
| bignate
| 346
| 2008-03-30 20:50:09
| this is about were my rad will sit in stock position.
long pump for a 85 monte ss 305
|
| bignate
| 278
| 2008-03-30 20:42:57
| this is the motor i put in my truck.
504. duration voodoo cam
proform timing gears and a 700
edlebrock carb to top it off
|
| spyda
| 232
| 2008-03-30 16:30:28
| Trans is from an 2002 WSA along with torque converter, dipstick tube and cooler lines - installing in my S10.
|
| spyda
| 235
| 2008-03-30 15:38:38
| dismantling the front clip on my 87 S10 for cleanup/prep.
|
| chrisrottie
| 221
| 2008-03-30 09:41:04
| you can see the position of the 6AL box and my my shifter. I have carpeting to go in as well as a little more heat insulation
|
| chrisrottie
| 256
| 2008-03-30 09:37:34
| still working on the wiring of the headlight switch but in the meantime have the old switch hooked up and hanging so the lights work
|
| chrisrottie
| 257
| 2008-03-30 09:36:10
| Fuel cell and battery box. waiting for warmer weather so I can stretch the tonneaus cover over it.
|
| chrisrottie
| 354
| 2008-03-30 09:33:55
| engine full installed and running just waiting to but the new transmission behind it and ready to go racing
|
| chrisrottie
| 269
| 2008-03-30 09:30:01
| more pics of dash with tach and 6al box where climate control is.
|
| chrisrottie
| 250
| 2008-03-30 09:28:56
| more pics of dash install
|
| goldeneagle
| 227
| 2008-03-29 21:40:30
| View of my 91 S10 with front clip removed. The engine and tranny will be trial fitted and then taken back out and the engine compartment and frame painted gloss black.
|
| goldeneagle
| 200
| 2008-03-29 19:22:02
| This is the left side view of my 91 S10. It was lowered 4 ins. when I bought it for $300.
|
| Bakas
| 165
| 2008-03-28 15:44:17
| my tig welding skills
|
| Bakas
| 120
| 2008-03-28 15:43:19
| the new 9 inch
|
| ugot8up
| 211
| 2008-03-27 19:25:07
| sbc s10 daily driver now...with some potential
|
| smallblock283
| 214
| 2008-03-25 19:25:31
| took off the a/c box much more room
|
| smallblock283
| 190
| 2008-03-25 19:23:47
| it has dual 2.5 inch in/out. its the bigblock 2 ser.
|
| smallblock283
| 180
| 2008-03-25 19:20:24
| 4 inch lowing block withlakewood traction bars
|
| smallblock283
| 211
| 2008-03-25 19:18:29
| this gives alot of wheel travel for the 4 inch drop
|
| smallblock283
| 173
| 2008-03-25 19:16:27
| what a basket case
|
| smallblock283
| 185
| 2008-03-25 19:15:30
| man what a piece, the woman said the day i showed up with the truck
|
| smallblock283
| 191
| 2008-03-25 19:13:52
| cut out the heater put in some switchs and some gauges
|
| smallblock283
| 212
| 2008-03-25 19:11:08
| got this stuff from autozone looks like carbon fiber
|
| smallblock283
| 232
| 2008-03-25 19:05:18
| Almost got it back together looks nice!
|
| z28kila
| 199
| 2008-03-22 19:25:38
| just got done with it, ready to reinstall into the truck and get it running again.
|
| badandy
| 291
| 2008-03-20 02:42:20
| 93 Chey S10 Dropped 5 inches all around Bell Tech coil springs leaf springs spindels blocks nitro shocks 305 CI TBI NV 3500 out of S10 ZQ8 sway bars and steering box .
|
